 0086-574-86322282      sales@ltkey.com 

Catagory List

Contact Us

Tel: +86-574-86322282
Fax: +86-574-86322283
Email: sales@ltkey.com
Add: NO. 210, Shounan E-commerce Venture Park, No. 88, Xuefu Road, Yinzhou District, Ningbo, China.

loading

Share to:
sharethis sharing button

3mm Yellow Round LED Lamp with Yellow Diffused

Availability:
Quantity:
  • LL30UY3D60-200

  • LITEKEY

  • 8541401000

3mm Yellow Round LED Lamp(LL30UY3D60-200)

·Package Dimensions  

Notes:

1. All dimension units are millimeters.

2.All dimension tolerance is ±0.15mm


·Selection Guide


Part No.

Dice

Lens Color

Iv(mcd)(IF=20mA)

Viewing Angle

(2θ½)

Raw Material

Emitted Color

MIN

TYP

MAX



LL30UY3D60-200

AlGaInP

Yellow

Yellow Diffused

100

200

--

60º


·Absolute Maximum Ratings(Ta=25Cº)

Item

Symbol

Maximum

Unit

Power Dissipation

PD

78

mW

Peak Forward Current (1/10 Duty Cycle 0.1ms Pulse Width)

IFP

90

mA

Continuous Forward Current

IFmax

30

mA

Reverse Voltage

VR

5

V

Electrostatic discharge

ESD

1000

V

Operating Temperature Range

Topr / Tstg

-40 to+85

Storage Temperature Range

Topr / Tstg

-40 to+100


·Electrical / Optical Characteristics(Ta=25Cº)

Item

Symbol

Min.

Typ.

Max.

Unit

Condition

Peak Wavelength

λp

-

596

-

nm

IF=20mA

Dominant Wavelength

λd

-

590

-

nm

IF=20mA

Spectral Line Coordinates

Δλ

-

20

-

nm

IF=20mA

Forward Voltage

VF

-

2.0

2.6

V

IF=20mA

Reverse Current

IR

-

-

10

uA

VR=5V

LED lamp Wavelength

NOTES:

1.All dimensions are in millimeter(inch);

2.Tolerance is ±0.25mm(0.01˝) unless other specified; Luminous intensity tolerance is ±10%;

3.Dominant Emission Wavelength tolerance is ±1nm; Specifications are subject to change without notice.


·Typical Electro-Optical Characteristic Curve:


FIG. 1 Forward Current Vs. Forward Voltage      FIG. 2 Relative Intensity Vs .Forward Current

     

     

FIG. 3 Forward Voltage Vs. Temperature        FIG. 4 Relative Luminosity Vs. Temperature

             

         


FIG. 5 Relative Intensity Vs. Wavelength




LED lamp production

LED lamp testing

·Recommended Wave Soldering Profiles:

Notes:

1.Recommend pre-heat temperature of 105℃ or less (as measured with a thermocouple  

 attached to the LED pins) prior to immersion in the solder wave with a maximum solder bath

 temperature of 260℃.

2.Peak wave soldering temperature between 245-255℃ for 3 sec (5 sec max).

3.Do not apply stress to the epoxy resin while the temperature is above 85℃.

4.Fixtures should not apply stress on the component when mounting and soldering process.

More than one wave soldering is not allowed.




·Terms and conditions for the usage of this document

1. The information included in this document reflects representative usage scenarios and intended for technical reference only.

2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications.

3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, LITEKEY will not be responsible for any subsequent issues.

The information in this document applies to typical usage in consumer electronics applications. If customer’s application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with LITEKEY representative for further assistance.





1.Storage conditions:

a. Prevent continued exposure to the condensing moisture environment and keep the product away from rapid transitions in ambient temperature.

b. LEDs should be stored with temperature ≤30℃ and relative humidity ≤60%。

c. Product in the original sealed package is recommended to be assembled within 72 hours of opening. Product in opened package for more than a week should be baked for 30 (+10/-0) hours at 85-100℃.

2. The lead pitch of the LED must match the pitch of the mounting holes on the PCB during component. Lead-forming may be required to insure the lead pitch matches the pitch. Refer to the figure below for proper lead forming procedures. (Fig.①)





4. During lead forming, use tools or jigs to hold the leads securely so that the bending force will not be transmitted to the LED lens and its internal structures. Do not perform lead forming once the component has been mounted onto the PCB.(fig.④)

5. Do not bend the leads more than twice. (fig.⑤)

6. During soldering, component covers and holders should leave clearance to avoid placing damaging stress on the LED during soldering




7. Through-hole LEDs are incompatible with reflow soldering.

8. Cleaning:

a. At room temperature, cleaning should occur only with isopropyl alcohol for a duration of no more than one minute when necessary. Dry at room temperature before use.

b. Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such ultrasonic power and the assembled condition. Ultrasonic cleaning shall be pre-qualified to ensure this will not cause damage to the LED.

9. Other:

a. Above specification may be changed without notice. LITEKEY will reserve authority on material change for above specification.

b. When using this product, please abserve the absolute maximum ratings and the instructions for using outlined in these specification sheets. LITEKEY assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets.


These specification sheets include materials protected under copyright of LITEKEY COMPANY LIMITED. Please don’t reproduce cause by anyone to reproduce them without LITEKEY’s consent.



Previous: 
Next: 

News

Leave a Message
​Copyright © LITEKEY. All Rights Reserved. Site Map